- How much HP does a 383 stroker make?
- How much does a 327 engine weigh?
- Can you stroke a 327?
- How much HP can you get out of a 327?
- How do you tell a 327 from a 350?
- Which is the best LS engine?
- What is the most reliable Chevy engine?
- Why is a 327 better than a 350?
- Will a 350 intake fit a 327?
- When did Chevy stop making the 327?
- How much does it cost to rebuild a 327 engine?
- What Chevy motor has the most horsepower?
- Will a 350 intake fit a 400?
- Did Chevrolet ever make a 327 4 bolt main?
- Is a 5.3 Chevy engine a 327?
- What is the difference between a 283 and 327?
- Will a 350 intake fit a 305?
How much HP does a 383 stroker make?
The point here is 502 lb-ft at 4,700 rpm and 500-plus horsepower from 5,700-6,200 rpm.
Someday we hope to stab this 383 in the Crusher Camaro, which has been relieved of its 632….Hot Rod’s Proven Recipe For A Simple Chevy 383 That Knocks Down 500 HP And 500 LB-FT.True 383 PowerRPMLB-FTHP6,1004315016,20042550221 more rows•Oct 13, 2009.
How much does a 327 engine weigh?
about 530 lbs.So there you have it – the 327 weighs about 530 lbs.
Can you stroke a 327?
As the others said, yes you can but it would be cheaper and wiser just to pick up a 350 block and stroke it, dress it up as a 327. Or, get a good 400 block and do the same.
How much HP can you get out of a 327?
Rated at 375 hp, the fuel-injected 327 was a high-winding screamer, as satisfying to drive as any big-block. At the other end of the spectrum, the 327 was also offered at much more pedestrian power levels, as low as 210 hp (gross).
How do you tell a 327 from a 350?
The compression height of the piston (1.67 for a 327; 1.56 for A 350), or the casting number on the crankshaft should tell you what it actually is.
Which is the best LS engine?
In short, the best engine for your LS or Vortec swap is the one you can afford. Sure, we would all love a shiny new LS3 crate engine from Chevrolet Performance or a rebuilt 5.3L long-block from Summit Racing, but once we crunch the numbers that’s not always possible.
What is the most reliable Chevy engine?
Dependable Chevys: These are the Most Reliable Silverado Engines6.0-Liter V-8 Hybrid. … 6.0 L Vortec 6000 V8. … 5.3-Liter V-8. … 4.3-Liter V-6. … 6.2-Liter V-8. … Duramax 6.6-Liter Turbo-Diesel V-8.
Why is a 327 better than a 350?
A 327 with it’s shorter stroke would need shorter gears so it can GET to its revs, where a 350, with its slightly longer stroke and more torque output will pull a little taller gear than the 327 will. … Never underestimate the importance of gearing. It is every bit as important as the engine itself.
Will a 350 intake fit a 327?
It’s a bolt on fit. You will have an issue with the PCV, there are several threads on workarounds but the 327 had a hole near the distributor that the PCV pipe bolted to which is not on the 350 block.
When did Chevy stop making the 327?
The last iteration of the 327 appeared in 1969 with a two-barrel carburetor and a 9-to-1 compression ratio that produced 235 horsepower and 325 foot pounds of torque, but by then another Chevrolet small-block had already appeared on the market and had begun stealing what thunder the 327 had left.
How much does it cost to rebuild a 327 engine?
FNF01, $3000-$9000 for a rebuild is an absolute Rip Off. Your also dreaming if you think your 327 will be putting out 400 HP. You can buy a brand new 350, 290 HP Crate motor for right at $2000 that includes a warrantee. Its a No Brainer.
What Chevy motor has the most horsepower?
As the power behind the 2019 Corvette ZR1, the new supercharged 6.2L LT5 represents the pinnacle of Chevrolet’s performance: It’s the most powerful engine ever offered in a Chevy production vehicle.
Will a 350 intake fit a 400?
Yes they will fit, a 400 is diffrent internally from a 350 or 305 etc.
Did Chevrolet ever make a 327 4 bolt main?
They never made a 327 4 bolt main block. You can make one with a large journal 327 crank in a 4 bolt 350 block due to the same bore that they have.
Is a 5.3 Chevy engine a 327?
Chevy used to have a 327 which was the 5.4L engine. Now they call it the 5.3L engine so it is the old 327 down sized slightly to a 323.
What is the difference between a 283 and 327?
There is a “wing” looking thingy above the front cover that sticks out of the block. On a 283 you can’t lay your finger in the indentation, on a 327 you can. Hard to explain but easy to see if you know the difference. Easy tell back in the day.
Will a 350 intake fit a 305?
Everything fits the same it’s the same block you can’t tell the difference except the 350 sticker on the valve covers. I did the same swap but put a performer manifold on. The 305 /350 bolt holes are identical to the thread.